|
Last Modified:
08-30-2021
|
6.10:8.0.50
|
Doc ID:
RM10000000191VO
|
|
Model Year Start:
2018
|
Model:
Prius
|
Prod Date Range:
[11/2017 - 08/2019]
|
|
Title:
INTERIOR PANELS / TRIM: LOWER INSTRUMENT PANEL: INSTALLATION; 2018 - 2019 MY Prius [11/2017 - 08/2019]
|
INSTALLATION
PROCEDURE
1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(a) When installing a new lower instrument panel assembly, No. 1 instrument panel sub-assembly or lower instrument panel sub-assembly:
(1) Immediately before installing the lower instrument panel assembly, twist and cut off the portion as shown in the illustration.
|
*A
|
except 11.6 Inch Display
|
*B
|
for 11.6 Inch Display
|
(b) except 11.6 Inch Display:
(1) Install the lower instrument panel sub-assembly with the 2 bolts <A>, 4 bolts <B>, 3 screws <C> or <G> and screw <D>.
|
*a
|
Bolt <A>
|
*b
|
Bolt <B>
|
|
*c
|
Screw <C> or <G>
|
*d
|
Screw <D>
|
|
*e
|
Clip
|
-
|
-
|
NOTICE:
-
Do not damage the lower instrument panel sub-assembly.
-
Do not allow the wire harnesses to interfere with the surrounding parts.
-
If a screw <C> is loose and cannot be installed securely, replace it with a screw <G>.
Torque:
Bolt <A> :
20 N·m {204 kgf·cm, 15 ft·lbf}
Bolt <B> :
13 N·m {133 kgf·cm, 10 ft·lbf}
(2) Install the 2 clips.
(3) Engage each clamp.
|
*A
|
w/ Telematics Transceiver
|
*B
|
w/ Satellite Radio
|
(4) Connect each connector.
(c) for 11.6 Inch Display:
(1) Install the lower instrument panel sub-assembly with the 2 bolts <A>, 6 bolts <B>, 3 screws <C> or <G> and screw <D>.
|
*a
|
Bolt <A>
|
*b
|
Bolt <B>
|
|
*c
|
Screw <C> or <G>
|
*d
|
Screw <D>
|
|
*e
|
Clip
|
-
|
-
|
NOTICE:
-
Do not damage the lower instrument panel sub-assembly.
-
Do not allow the wire harnesses to interfere with the surrounding parts.
-
If a screw <C> is loose and cannot be installed securely, replace it with a screw <G>.
Torque:
Bolt <A> :
20 N·m {204 kgf·cm, 15 ft·lbf}
Bolt <B> :
13 N·m {133 kgf·cm, 10 ft·lbf}
(2) Install the 2 clips.
(3) Engage each clamp.
|
*A
|
w/ Telematics Transceiver
|
*B
|
w/ Satellite Radio
|
(4) Connect each connector.
(d) Engage the 2 claws to connect the cooler (room temp. sensor) thermistor as shown in the illustration.
|
Install in this Direction
|
(e) Engage the 4 clips and 2 claws to connect the lower instrument cover sub-assembly to the upper steering column cover.
2. CONNECT NO. 2 INSTRUMENT PANEL WIRE
Click here
3. INSTALL GLOVE BOX LIGHT ASSEMBLY
Click here
4. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
(a) Engage the 4 clips to install the No. 2 instrument panel register assembly as shown in the illustration.
|
Install in this Direction
|
5. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
(a) Engage the 4 clips to install the No. 1 instrument panel register assembly as shown in the illustration.
|
Install in this Direction
|
6. INSTALL NO. 2 LOWER INSTRUMENT PANEL FINISH PANEL
(a) Engage the 9 clips to install the No. 2 lower instrument panel finish panel as shown in the illustration.
|
Install in this Direction
|
7. INSTALL SHIFT LEVER HOLE COVER
(a) Connect each connector
(b) Engage the 5 clips to install the shift lever hole cover as shown in the illustration.
|
Install in this Direction
|
8. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
(a) Connect each connector
(b) Engage each clamp.
(c) Engage the 5 clips to install the lower center instrument cluster finish panel sub-assembly as shown in the illustration.
|
Install in this Direction
|
9. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
(a) Engage the claw to install the glove compartment door stopper sub-assembly.
10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
(a) Hold the glove compartment door assembly at an angle approximately 64.2° from its closed position and engage the 2 hinges horizontally as shown in the illustration.
|
*a
|
64.2°
|
-
|
-
|
|
Install in this Direction
|
-
|
-
|
NOTICE:
Engaging the hinges from an upward angle will deform the hinges. Be sure to install the glove compartment door assembly horizontally.
|
(b) Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows shown in the illustration and engage the stoppers to install the glove compartment door assembly.
|
|
|
*1
|
Glove Compartment Door Stopper Sub-assembly
|
|
|
(c) Engage the claw to connect the glove compartment door stopper sub-assembly.
11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Connect the connector.
(b) Engage the 2 guides as shown in the illustration.
|
Install in this Direction
|
(c) Engage the 3 claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
|
Install in this Direction
|
12. INSTALL COWL SIDE TRIM BOARD RH
HINT:
Use the same procedure as for the LH side.
Click here
13. INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
14. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (except 11.6 Inch Display)
for Radio and Display Type:
Click here
15. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (except 11.6 Inch Display)
for Navigation Receiver Type:
Click here
16. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (except 11.6 Inch Display)
(a) Engage the clamp.
(b) Connect each connector.
(c) Engage the 5 guides and 18 clips to install the center instrument cluster finish panel sub-assembly as shown in the illustration.
|
Install in this Direction
|
-
|
-
|
(d) Install the clip.
17. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY WITH NAVIGATION RECEIVER ASSEMBLY (for 11.6 Inch Display)
(a) Engage the clamp.
(b) Connect each connector.
(c) Engage the 5 guides and 16 clips to install the center instrument cluster finish panel sub-assembly with navigation receiver assembly as shown in the illustration.
|
Install in this Direction
|
-
|
-
|
(d) Install the 2 bolts <B>.
(e) Install the clip.
18. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL UPPER (for 11.6 Inch Display)
(a) Engage the front pillar garnish clip to the lower instrument panel sub-assembly.
HINT:
Make sure that the front pillar garnish clip is engaged correctly.
|
*1
|
Front Pillar Garnish Clip
|
*2
|
Lower Instrument Panel Sub-assembly
|
|
*a
|
Correct
|
*b
|
Incorrect
|
(b) Engage the 7 clips, 2 claws and front pillar garnish clip to install the center instrument cluster finish panel upper as shown in the illustration.
|
Install in this Direction
|
19. INSTALL INSTRUMENT PANEL FINISH PANEL END RH
(a) Engage the 3 guides as shown in the illustration.
|
Install in this Direction
|
(b) Engage the 6 clips to install the instrument panel finish panel end RH as shown in the illustration.
|
Install in this Direction
|
20. INSTALL COMBINATION METER ASSEMBLY
Click here
21. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here
22. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
(a) Connect the connector.
(b) Engage the 2 guides and 6 clips as shown in the illustration.
|
Install in this Direction
|
(c) Install the lower instrument panel finish panel assembly with the screw <C>.
23. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
(a) Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
24. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Connect the connector.
(b) Engage the guide as shown in the illustration.
|
Install in this Direction
|
(c) Engage the claw as shown in the illustration.
|
Install in this Direction
|
(d) Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <F>.
25. INSTALL COWL SIDE TRIM BOARD LH
Click here
26. INSTALL FRONT DOOR SCUFF PLATE LH
Click here
27. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
(a) Connect each connector.
(b) Engage the claw and 4 clips to install the instrument cluster finish panel garnish assembly as shown in the illustration.
|
Install in this Direction
|
28. INSTALL INSTRUMENT PANEL FINISH PANEL END LH
(a) Engage the 3 guides as shown in the illustration.
|
Install in this Direction
|
(b) Engage the 6 clips to install the instrument panel finish panel end LH as shown in the illustration.
|
Install in this Direction
|
29. INSTALL REAR CONSOLE BOX ASSEMBLY
Click here
30. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
Click here
31. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
32. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
33. INSPECT SRS WARNING LIGHT
Click here
|